Manufacturing Book List
|
Manufacturing Book List |
|
|
|
|
||
|
|
||
|
|
| Camarinha-Matos, L. and H. Afsarmanesh (1996). Balanced automation systems II: implementation challenges for anthropocentric manufacturing: proceedings of the 2nd IEEE/ECLA/IFIP International Conference on Architectures and Design Methods for Balanced Automation Systems, Portugal, June 1996. London; New York, Chapman & Hall. |
| Camarinha-Matos, L. and H. Afsarmanesh (1996). Balanced automation systems II: implementation challenges for anthropocentric manufacturing. London, Chapman & Hall on behalf of the International Federation for Information Processing. |
| Camarinha-Matos, L., H. Afsarmanesh, et al. (1998). Intelligent systems for manufacturing: multi-agent systems and virtual organizations: proceedings of the BASYS '98 - 3rd IEEE/IFIP International Conference on Information Technology for Balanced Automation Systems in Manufacturing, Prague, Czech Republic, August 1998. Boston, Mass.; London, Kluwer Academic Publishers. |
| Campbell, R. I. E. (1998). Proceedings of the 7th European conference on rapid prototyping and manufacturing. Nottingham, Univ of Nottingham. |
| Cannon, C. M. (1988). Sources of comparative advantage in manufacturing. Canterbury, University of Kent. |
| Cao, J. E. and W. J. E. Endres (2002). Proceedings of the ASME Manufacturing Engineering Division 2002, ASME. |
| Capettini, R. E. and D. K. E. Clancy (1988). Cost accounting, robotics and the new manufacturing environment: 1st Annual management accounting symposium: Edited papers. Sarasota, Florida, American Accounting Association. |
| Capling, A. and B. Galligan (1992). Beyond the protective state: the political economy of Australia's manufacturing industry policy. Cambridge, Cambridge University Press. |
| Carmichael, E. A. and Y. Adachi (1978). Canada's manufacturing sector: performance in the 1970s. Ottawa, Conference Board in Canada. |
| Case, K. and S. T. Newman (1994). Advances in manufacturing technology VIII: proceedings of the tenth National Conference on Manufacturing Research, Loughborough University of Technology. 1994. London, Taylor & Francis. |
| Case, K. E. and S. T. E. Newman (1994). Advances in manufacturing technology VIII: 10th National conference on manufaturing research: Papers, Taylor & Francis. |
| Cassell, D. A. (1972). Introduction to computer-aided manufacturing in electronics. New York; [Chichester], Wiley-Interscience. |
| Caulkin, S. (1989). The new manufacturing: minimal IT for maximum profit. London, Economist Publications. |
| Centre for Achievement in Manufacturing, M. (1997). A model of manufacturing 'best practice' for SME's, Centre for Achievement in Manufacturing Management. |
| Champion, E. R. (1992). Finite element analysis in manufacturing engineering. New York; London, McGraw-Hill. |
| Chan, C. L. E., F. P. E. Incropera, et al. (1993). Transport phenomena in nonconventional manufacturing and materials processing: Symposium: Winter annual meeting: Papers, ASME. |
| Chan, K. C. E., C. Y. E. Tang, et al. (2003). Proceedings of the 9th International manufacturing conference, Elsevier. |
| Chandler, J. R. (1989). Advances in manufacturing technology IV: 5th National conference on production research: Papers, Kogan Page. |
| Chandler, J. R. and R. G. Barwick (1983). Flexible manufacturing systems and associated technologies: a one-day workshop presented by Huddersfield Polytechnic Engineering Systems Department in co-operation with the Engineering Industry Training Board (North-East Region) Wednesday 23 November 1983. [Huddersfield] ([Queensgate, Huddersfield HD1 3DH]), Huddersfield Polytechnic. |
| Chandra, A. and S. Mukherjee (1997). Boundary element methods in manufacturing. New York; Oxford, Oxford University Press. |
| Chandra, S. (1997). Waste materials used in concrete manufacturing. Park Ridge, N.J., Noyes Publications. |
| Chandra, T. E. (2001). Keynote papers presented at the proceedings of THERMEC'2000: the international conference on processing and manufacturing of advanced materials, Elsevier. |
| Chandra, T. E., J. M. E. Torralba, et al. (2003). Thermec'2003: international conference on processing and manufacturing of advanced materials, Trans Tech Publications. |
| Chaturvedi, P. E. (1998). Modern trends in manufacturing technology, Concept Publishing Company. |
| Chawdhry, P., R. Roy, et al. (1998). Soft computing in engineering design and manufacturing. London; New York, Springer. |
| Chedmail, P. E., J. C. E. Bocquet, et al. (1997). Integrated design and manufacturing in mechanical engineering: proceedings of the 1st IDMME conference held in Nantes, France, 15-17 April 1996. Dordrecht; London, Kluwer Academic Publishers. |
| Chen, D. E. (2001). Semiconductor optoelectronic device manufacturing and applications, SPIE. |
| Chen, X. E., T. E. Fujioka, et al. (2000). High-power lasers in manufacturing, SPIE. |
| Cheng, k. E. and D. E. Webb (2002). Advances in manufacturing technology XVI. Bury St Edmunds, Professional Engineering Pub. |
| Cheng, K. E. and D. E. Webb (2003). Advances in manufacturing research in the UK, Freund. |
| Cheng, T. C. E., S. Podolsky, et al. (1996). Just-in-time manufacturing: an introduction. London, Chapman & Hall. |
| Childe, S. J. (1999). Proceedings of the Second International Conference on Stimulating Manufacturing Excellence in Small and Medium Sized Enterprises (SMESME): 29th - 31st March 1999, Plymouth, United Kingdom. Plymouth, Manufacturing and Business Systems Research Group, University of Plymouth. |
| Childe, S. J. (2004). 5th Managing innovative manufacturing conference, Taylor & Francis. |
| Chilton, K. W., M. E. Warren, et al. (1990). American manufacturing in a global market: Conference on American manufacturing in the 1990's: Edited transcriptions. Norwell, Mass., USA, Kluwer Academic Publishers. |
| Chilton, K. W., M. E. Warren, et al. (1990). American manufacturing in a global market. Boston[Mass.]; London, Kluwer Academic. |
| Chong, K. P., B. R. Dewey, et al. (1989). University programs in computer-aided engineering, design, and manufacturing: Annual conference: Papers. New York, N.Y., American Society of Civil Engineers. |
| Christer, A. H. E., S. E. Osaki, et al. (1997). Stochastic modelling in innovative manufacturing, Springer. |
| Ciampa, D. (1988). Manufacturing's new mandate, Wiley. |
| Clarke, S. R. (1988). Aspects of the design and control of manufacturing systems subject to demand uncertainty. Birmingham, University of Aston. |
| Clement, J., A. Coldrick, et al. (1992). Manufacturing data structures: building foundations for excellence with bills of materials and process information. Essex Junction, VT, Oliver Wight; Chichester: Wiley [distributor]. |